Resources » Medium Voltage vs Low Voltage Equipment

Medium Voltage vs Low Voltage Equipment

by | Nov 5, 2026

Low voltage generally means equipment operating at or below 1,000 volts, and medium voltage covers the band above that up to roughly 35 kV, though the exact boundaries vary between standards. In a data center the distinction decides far more than a number on a drawing: it changes the physical size of the equipment, the copper required to carry the load, who is qualified to work on it, how much space the electrical rooms consume, and how long the equipment takes to procure.

Where the boundary actually sits

There is no single universal definition, which is a common source of confusion when specifications cross between standards bodies or between regions.

Most commonly, low voltage covers equipment operating at or below 1,000 V AC. Medium voltage picks up above that and runs to somewhere between 35 kV and 69 kV depending on which standard is being applied. Above that range the terminology moves to high voltage, which in a data center context is normally the utility’s concern rather than the facility’s.

In practice, data center work sits almost entirely in two bands: distribution at 480 V or 400 V on the low voltage side, and 5 kV to 35 kV classes on the medium voltage side.

Because the classification governs which code requirements, clearance rules and qualification standards apply, the controlling definition is whichever one your applicable code and jurisdiction uses. Confirm it with the engineer of record rather than assuming the figure quoted in a product datasheet applies to your project.

Where each one appears in a data center

Power arrives at medium voltage and gets stepped down. Where that step-down happens is the design decision, and it has moved over time.

Typical voltage class by stage
Stage Typical class What sits here
Utility service Medium or high voltage Incoming service, metering, primary switchgear
Site distribution Medium voltage MV switchgear, feeders to building or block
Step-down MV to LV Service transformers
Building distribution Low voltage Switchboards, UPS, generators, automatic transfer switches
Data hall distribution Low voltage Remote power panels, busway, floor PDUs
Rack Low voltage Rack PDUs, server power supplies

The traditional pattern steps down to low voltage early, near the building entrance, and distributes 480 V across the facility. That works well at moderate load and moderate distances.

As campus sizes and densities have grown, the step-down has tended to move later and closer to the load. Distributing at medium voltage across a site and transforming near the data hall reduces the current carried over distance, which is where most of the practical benefit lies.

What changes when you distribute at medium voltage

Six things shift, and they do not all point the same way.

  • Conductor size falls sharply. Power is the product of voltage and current, so carrying the same load at a higher voltage means less current. Less current means smaller conductors, less copper or aluminum, lighter containment and less congested routes. Over long distances this is the dominant economic argument.
  • Losses fall. Resistive losses rise with the square of current. Halving the current cuts those losses to a quarter, which matters both for running cost and for the heat deposited in electrical rooms.
  • Equipment gets physically larger per unit. Medium voltage switchgear needs greater clearances and insulation, so an individual line-up occupies more floor space and height than its low voltage equivalent. The space saving comes from needing fewer, smaller feeders, not from smaller gear.
  • Qualification requirements rise. Work on medium voltage equipment requires specifically qualified personnel, different procedures and different protective equipment. Electrical hazards can be more severe and require additional safety precautions. This affects staffing, contractor selection and maintenance cost over the life of the facility.
  • Protection and coordination get more involved. Medium voltage systems require a coordination study, relay settings and often more sophisticated protection schemes than a low voltage distribution board. That is engineering effort at design stage and commissioning effort at the end.
  • Procurement gets harder. Medium voltage switchgear and transformers are built by fewer manufacturers than their low voltage equivalents, and the supplier base narrows further as voltage class rises. That shows up in the delivery date long before it shows up in the price.

How to think about the decision

The choice is rarely binary. Every data center uses both. The real question is where the transition point sits, and that is driven by three things.

Distance

The further power has to travel, the stronger the case for carrying it at medium voltage. On a large campus, low voltage distribution to a remote building means either very large conductors or unacceptable voltage drop. On a single compact building, the argument is much weaker.

Load

Higher total load pushes the same way. At modest capacity, low voltage distribution is straightforward and the added complexity of medium voltage buys little. As capacity rises, the current required at 480 V becomes impractical to carry and distribute.

Phasing and growth

A site built out in phases benefits from medium voltage distribution with transformers added per phase, because the backbone is sized once and the step-down capacity grows with the load. A single-phase build has less to gain from that flexibility.

A useful framing: medium voltage distribution trades capital cost and operational complexity for reduced conductor cost, lower losses and better scalability. On a small, compact, single-phase facility that trade usually loses. On a large, distributed, phased campus it usually wins. Most projects sit somewhere in between and the answer comes from running both options against the actual site.

Specification points that matter at each level

Whichever side of the boundary a piece of equipment sits on, a few parameters consistently cause trouble when they are left vague.

Specification considerations by voltage class
Consideration Low voltage Medium voltage
Fault current Determined largely by transformer impedance Determined by source and system impedance; coordination study required
Equipment construction Switchboards, panelboards, fixed breakers Metal-clad or metal-enclosed switchgear, often draw-out breakers
Clearances Modest Significant; affects room dimensions and access routes
Protection Breakers with integral trip units Protective relays, CTs and PTs, settings from a coordination study
Maintenance access Generally front access Front and often rear access; racking space for draw-out breakers
Qualified personnel Standard electrical qualification Specific medium voltage qualification and procedures
Supplier base Broad Narrower, and narrows further as class rises

The clearance and access point is the one most often discovered late. Medium voltage equipment needs room around it for operation and maintenance, and that requirement is not negotiable once the gear is selected. Electrical room dimensions should be set from the equipment, not the other way around.

Next step

Trilogy engineers and supplies equipment on both sides of the boundary, from medium voltage switchboards and integrated power skids and transformers through to low voltage distribution and rack-level power. If you are weighing where the step-down should sit on a specific site, get in touch.

Frequently asked questions

What is the difference between medium voltage and low voltage?

Low voltage generally refers to equipment operating at or below 1,000 volts AC. Medium voltage covers the band above that, typically up to somewhere between 35 kV and 69 kV depending on the standard being applied. The exact boundaries differ between standards bodies and regions, so the controlling definition for any project is the one used by the applicable code and jurisdiction. Confirm it with the engineer of record.

Why do data centers distribute power at medium voltage?

Because carrying the same load at a higher voltage requires less current, which means smaller conductors and lower resistive losses. Losses rise with the square of current, so halving the current cuts them to a quarter. Over long distances and at high total load, those savings outweigh the added cost and complexity of medium voltage equipment. On small, compact facilities the trade usually goes the other way.

Does medium voltage equipment take up more or less space?

Both, depending on what you measure. An individual medium voltage switchgear line-up needs greater clearances and insulation, so it occupies more floor space and height than a comparable low voltage assembly. But distributing at medium voltage requires fewer and smaller feeders across the site, so the total space given over to electrical distribution can fall. Clearance requirements should set electrical room dimensions rather than being fitted into them.

Is medium voltage equipment harder to procure than low voltage?

Generally yes. Medium voltage switchgear and transformers are built by fewer manufacturers than their low voltage equivalents, and the supplier base narrows further as voltage class rises. A project sitting marginally above a voltage class boundary is worth checking specifically, since the higher class can carry meaningfully longer delivery for reasons unrelated to the project itself.

Related Articles

Ready To Get Started?

Tell us about your next project!
Speak with a Trilogy team member today.